Pressure Washers

President's Day

2012-02-20T09:04:00.000-08:00

Remember to buy American made products built by American owned companies! Especially, on President's Day. George and Abe would want it no other way! Mention this Blog through the end of February 2012 and receive an extra 10% off any pressure washer, parts, or detergent purchases! Visit our Website at www.Aquatech-USA.com or "Like" us on Facebook @ www.Aquatech-USA.com

Winterizing Your Pressure Washer

2012-01-04T08:59:00.000-08:00

If you store your pressure washer in an area below 32 degrees F, make sure you winterize your machine. Otherwise, the damage of a freeze up can be very costly. Please contact our service department for instructions on winterizing your pressure washer or store your pressure washer in a heated area that will not go below 32 degrees F. Remember an ounce of prevention is worth a pound of cure. www.Aquatech-USA.com

Veterans Day

2011-11-11T10:10:00.000-08:00

We want to thank all of our Veterans for their service and dedication. We are grateful for your sacrifices and devotion to protecting our FREEDOMS to be AMERICANS! We especially want to thank two of our employees, Jim Mastrian and John Kimble. Remember to thank our Vets not just on Veteran's Day but continually and often! It's the least we can do!

Built in the USA-Pressure Washers and beyond

2011-08-10T13:26:00.000-07:00

These days it seems harder to find pressure washers that are built in the USA. Could it be that Americans have settled to buy equipment based on price? Pressure washers built outside the USA tend to have a limited parts availability, materials of inferior quality, and even no product support. Americans seem to continue to buy cheap pressure washers and once they fail you throw the product away and buy a new one. What I consider as a "throw away mentality".

But let's think about what purchasing a USA built pressure washer can do for our failing economy. If the company is building the pressure washer in the USA, it would employ Americans and keep the spendable income in the USA. If the materials being used are sourced in the USA, more employment and better parts availability. If the pressure washer is built to last by using components that can be rebuilt, employment for service support dealers throughout the USA.

Please consider these points when buying not just a pressure washer but any products. The price of a USA built pressure washer might be 2 to 3 times more in some cases but price is not everything. Think of it as an investment into the future of the America economy and future generations.

Running Bleach through your pressure washer

2011-07-07T09:11:00.000-07:00

During the late Spring and early Summer, most people want to pressure wash their decks to remove mold or mildew. One of the best ways to remove the mold and mildew is to apply a diluted bleach solution to the deck and then pressure wash it off. I suggest that you use a pump up sprayer(similar to the one pictured) to apply the bleach solution versus running the bleach solution through your pressure washer. The bleach can do damage to the components in the pump, gun, injector and nozzle. When done using the pump up sprayer make sure you rinse through the sprayer with fresh clean water before storing away.

Pressure Washers: Pressure Washers Bypass

2011-05-02T10:20:00.000-07:00

Pressure Washers: Pressure Washers Bypass: "When operating your pressure washer make sure that you do not leave the pressure washer in bypass for more than a few minutes. Power washers..."

Pressure Washers Bypass

2011-05-02T09:21:00.000-07:00

When operating your pressure washer make sure that you do not leave the pressure washer in bypass for more than a few minutes. Power washers that have a trigger gun control on them most likely have an unloader or bypass valve. The unloader or bypass valve allows the pump to continue running after the trigger gun is released by recirculating or bypassing the water back through the pump via the unloader/bypass valve. When the water is recirculating through the pump, the water will build up friction heat and can reach temperatures beyond 180 degrees F within a few minutes and start to do major damage to the pressure pump, seals, check valves, unloader/bypass valve, ceramic pistons.

A couple ways to help prevent leaving a pressure washer in bypass is either open the trigger gun after 2 minutes of bypass time(this will allow fresh cooler water to displace the water that was in bypass) or shutdown the power washer after 2 minutes.

If you are purchasing a new pressure washer, there are a few options to consider that will help keep the machine from running in bypass for long periods of time.

Thermal Relief Valve-This affordable valve can be plumbed into the bypass line and when the water reaches a set temperature (around 140 degrees F), the valve will open and spill out the bypass water and replace it with fresh cooler water. Once the valve cools off, the thermal relief valve will reset itself.

Time Delay Shutdown-Mostly used on electrically powered pressure washers. When the trigger gun is released, a timer relay is activated to shutdown the electric motor after a set period on time. To restart the power washer, the operater must turn the pressure washer back on at the control panel or remote panel.

Automatic Start/Stop-Mostly used on electrically powered pressure washers. When the trigger gun is released, a pressure switch, vacuum switch or flow switch is activated to shutdown the electric motor immediately. To restart the power washer, the operater open the trigger gun, the switch is deactivated and the electric motor starts.

Clutch Driven System-Can be used on an electric or gas engine powered pressure washer. Used only on a belt driven power washer. When the pressure washer is turned on only the motor or engine turns, until the trigger gun is opened then a micro switch will engage the pump clutch. The pump will only turn when clutch is engaged, this keep the pressure washer from going into bypass.

Pressure Washer Startup

2011-04-05T08:57:00.000-07:00

It's Spring and this is the time of the year that a lot of people take their pressure washers out of winter storage to clean up around the house. One of the major problems that occurs upon startup of a pressure washer especially a hot water pressure washer that has been stored away for a period of time is debris gets clogged in the trigger gun, high pressure hose, or pressure nozzle. To avoid this problem, before you run any water through the machine disconnect the pressure hose, trigger gun/wand assembly and pressure nozzle. Then run the water through the pressure washer and start the pressure washer's engine or electric motor. Usually, the water will come out of the pressure washer looking very dark or black. Run the pressure washer for about 1 to 2 minutes until the water clears up. Shut off the pressure washer and water spigot, reconnect the pressure hose and trigger gun keeping the pressure nozzle off. Turn on the water and run the machine again. Release the trigger gun on and off a few times, make sure the water is coming out of the trigger gun clear and then install your pressure nozzle.

This will help keep your pressure washer be it a hot water or cold water pressure washer from clogging up the trigger gun, high pressure hose or pressure nozzle. You can contact me at info@aquatech-usa.com if you have any questions about your pressure washer or power washer.

Pressure Washers

2011-04-04T16:11:00.000-07:00

I have over 22 years of repairing, servicing, operating and selling pressure washers. I started this blog to help bring advise and my know how to the end users of pressure washer products. I hope I can help those of you who use pressure washers with my expertise and professionalism. If you find this information valuable, please visit my company's website at http://www.aquatech-usa.com/ and see the high quality heavy duty pressure washers that I sell and service with great customer support and knowledgable workforce in the pressure washer and power washing industry.